SRU520_87_v6.qxd 26-04-2005 14:37 Pagina 1 Universal GB SRU 520/87 Instructions for use 4 I Instruzioni per l'uso 11 Instrucciones de manejo 18 E P Manual de utilização 25 32 Návod k pouzití Instrukcja obslugi 39 46 53 GR RU CZ PL Quick, Clean & Easy Setup www.philips.com/urc SRU520_87_v6.qxd 26-04-2005 14:37 Pagina 2 SRU520_87_v6.qxd 26-04-2005 14:37 Pagina 3 1 ^ 2 3 4 5 6 7 8 $ # @ % 9 0 ! SRU520_87_v6.qxd 26-04-2005 14:38 Pagina 4 Instructions for use Contents 1. 2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installing the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Testing the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setting the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Keys and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Extra possibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Adjusting device selection (Mode keys) . . . . . . . . . . . . . . . . . . . . . . . . . 8 Adding a function to the remote control . . . . . . . . . . . . . . . . . . . . . . . . 8 Restoring the original functions of your remote control . . . . . . . . . . . . 9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Need help? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Code list of all brands / equipment . . . . . . . . . . . . . . . . . . . . . . . . . 60-73 English 4 3. 4. 5. 6. 1. Introduction Congratulations on your purchase of the Philips SRU520 universal remote control. After installing the remote control you can operate a maximum of 2 different devices with it:TV and VCR/DVD players/recorders. You can find information about how to prepare this remote control for use in the chapter `Installing the remote control'. 2. Installing the remote control Inserting the batteries 1 Press the cover inwards and slide it 2 3 in the direction of the arrow. Place two AAA type batteries into the battery compartment, as shown. Slide the cover back and click it firmly into place. Note: If the mode keys (TV and DVD/VCR) blink four times after every key press, the remote control is indicating that its batteries are running low. Replace the old batteries with two new AAA batteries. Testing the remote control The remote control has been programmed to operate most Philips devices. Because the SRU520 may use different signals for each brand and even for different models of the same brand, it is advisable to test whether your device responds to the SRU520.The example below (TV) instructs you how to do this.You can repeat the same steps for other devices (VCR/DVD players/recorders) which you want to operate using the SRU520. Example of TV: 1 Turn your TV on manually or use the original remote control. Tune to channel 1. 2 Press the TV key to select TV. Press the key until it lights up. ­ If the key does not light up, check whether the batteries are properly inserted (see `Inserting the batteries'). SRU520_87_v6.qxd 26-04-2005 14:38 Pagina 5 Instructions for use English 5 3 ­ Check whether all the keys are working. For an overview of the keys and their functions see `3. Keys and functions'. If the TV responds as it should to all of the key commands the SRU520 is ready for use. If the device does not respond at all or not to all of the key commands, follow the instructions under `Setting the remote control', or for online setup go to: www.philips.com/urc. · Setting the remote control This is only necessary if your device does not respond to the SRU520. If that is the case, the SRU520 does not recognize the brand and/or model of your device and you need to program the remote control to do so. The example below (TV) instructs you how to do this.You can repeat the same steps for other devices (VCR/DVD players/recorders) which you want to operate using the SRU520. You can set the remote control either automatically or manually. Automatically setting the remote control The remote control will now automatically search for the right code for your device. Example of TV: 1 Make sure the TV is switched on and select a channel using the original remote control or the keys on the TV (for example channel 1). The SRU520 emits the `switch off TV' signal for all models of TV that are stored in the memory. · If the device is a DVD-player or video recorder, insert a disk or tape and start playback. 2 Press the TV key to select TV. Press the key until it lights up. 3 Then keep keys 1 and 3 on the SRU520 pressed simultaneously for three seconds, until the key flashes twice and then remains lit. 4 Press and hold the Standby key of the SRU520. ­ The SRU520 now starts emitting all known `TV off ' signals, one by one. Each time a code is sent, the TV key lights up. SRU520_87_v6.qxd 26-04-2005 14:38 Pagina 6 Instructions for use 5 ­ When your TV switches off (stand-by), release the Standby key of the SRU520 immediately. The SRU520 has now found a code that works on your TV. Check if you can operate all functions on your TV with the SRU520. If this is not the case, you can redo the automatic setting. The SRU520 will then search for a code that works better. After the SRU520 has run through all the known codes, the search will stop automatically and the TV button stops flashing. Automatic programming of a TV takes a maximum of 5 minutes. For VCR/DVD this time is 2 minutes. English 6 6 · ­ ­ Manually setting the remote control Example of TV: 1 Turn on the TV manually or use the original remote control. Tune in to channel 1. 2 Look up the brand of your TV in the code list at the back of this manual. One or more four-figure codes are shown for each brand. Note the first code. Be careful! There are separate tables for TV, VCR and DVD. On our website www.philips.com/urc you can directly select your device typenumber to find the right code. Make sure you use the codes from the correct table. 3 Press the TV key to select TV. Press the key until it lights up. 4 Keep keys 1 and 3 pressed simultaneously for three seconds until the TV key flashes twice and then remains lit. 5 ­ 6 ­ Then enter the code noted in step 2 using the digit keys. The TV key will now flash twice. If the key flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Start again from step 2. Point the SRU520 at the TV and check that it responds as it should. If the TV responds to all of the key commands, the SRU520 is ready for use. Do not forget to note your code. If the device does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list. · SRU520_87_v6.qxd 26-04-2005 14:38 Pagina 7 Instructions for use English 7 3. Keys and functions The illustration on page 3 gives an overview of all keys and their functions. 1 y Standby . . . . . . . . switches TV,VCR or DVD on or off. 2 . . . - teletext on/off ( ); . . . - text mix ( ); . . . - text off ( ); - wide screen TV ( ); - enlarge ( ); - text hold ( ). 3 MENU . . . . . . . . . . . turns the menu on and off. 4 Cursor keys . . . . . . cursor up, down, left, right in a menu. 5 A/V. . . . . . . . . . . . . . . . switches between external inputs of your equipment. 6 s . . . . . . . . . . . . . . . . mutes the sound of the TV. 7 - VOL +. . . . . . . . . . . adjusts the TV volume. 8 Digit keys . . . . . . . . direct choice of channels and other functions. 9 SHIFT . . . . . . . . . . . for extra functions. When pressed at the same time as a second key, the second key will get another function. All blue labelled keys can be used together with SHIFT. For example: SHIFT + INSTALL installs your TV SHIFT + STORE. . stores TV settings Try out other combinations with the SHIFT-key on your device in order to find out which functions are available. Only functions featured on the original remote control are available. 0 5 . . . . . . . . . . . . . . . . - red teletext key - rewind (VCR/DVD) 2 . . . . . . . . . . . . . . . . - index - play (VCR/DVD) 6 . . . . . . . . . . . . . . . . - blue teletext key - wind (VCR/DVD) 9 . . . . . . . . . . . . . . . . - green teletext key - stop (VCR/DVD) 0 . . . . . . . . . . . . . . . . record ; . . . . . . . . . . . . . . . . . - yellow teletext key - pause (VCR/DVD) ! / . . . . . . . . . . . . . . . selects between one- and two-figure channel numbers. @ 2 . . . . . . . . . . . . . . . selects previous programme/channel. # - PROG + . . . . . . . . selects a previous or following channel. $ OK. . . . . . . . . . . . . . . confirms your selection. % BACK . . . . . . . . . . . . jumps back one level in the menu or turns off the menu. ^ TV - DVD/VCR . . . seletcs TV or DVD/VCR mode. If you use the (fi) 'memory off' key to get to the next teletext page on your Philips TV, you can press the STOP key for this. See also `Troubleshooting'. · If the device does not respond at all, or not to all of the key commands, follow the instructions under `Setting the remote control'. It is possible that you must enter another code for the device. SRU520_87_v6.qxd 26-04-2005 14:38 Pagina 8 Instructions for use 4. Extra possibilities Adjusting device selection (Mode keys) The SRU520 is default set for operating TV,VCR or DVD.You can select the device you wish to operate with TV and DVD/VCR selection buttons. Each key allows operation of one device only. If desired, you can program the keys to select a different kind of device. For example, if you want to operate a second TV. In the following example you will see how to configure the VCR/DVD key for a second TV. English 8 1 2 Switch on the second TV. Press the DVD/VCR key to select DVD/VCR. Press the key until the it lights up. 3 Then keep keys 1 and 6 on the SRU520 pressed simultaneously for three seconds, until the VCR/DVD key lights up. 4 Press keys 9, 9 and 2, in that order. 5 Press the TV key to select TV. Press the key until it lights up. 6 ­ Press the 1 key. The VCR/DVD key flashes twice. The VCR/DVD key will now allow you to operate your second TV. Program the SRU520 to operate the second TV. See `Setting the remote control'. 7 Adding a function to the remote control If you want to add a function to the SRU520, you can contact the Philips service line for Universal Remote Control to ask for the 5-figure code for the extra function. SRU520_87_v6.qxd 26-04-2005 14:38 Pagina 9 Instructions for use English 9 Restoring the original functions of your remote control 1 Keep keys 1 and 6 on the SRU520 pressed simultaneously for three seconds, until the mode key (TV or DVD/VCR) flashes twice and then remains lit. 2 ­ Press keys 9, 8 and 1 in that order. The mode key (TV or DVD/VCR) key flashes twice. All original functions have now been restored and any extra functions have been deleted. 5. Troubleshooting · ­ · ­ · ­ · ­ · ­ Problem Solution The mode keys (TV and DVD/VCR) blink four times after every key press. The remote control is indicating that its batteries are running low. Replace the old batteries with two new 1.5 Volt, AAA batteries. The device you want to operate does not respond and the mode key (TV or DVD/VCR) does not flash when you press a key. Replace the old batteries with two new 1.5 Volt, AAA batteries. The device you want to operate does not respond but the mode key (TV or DVD/VCR) does flash when a key is pressed. Point the SRU520 at the device and make sure that there are no obstructions between the SRU520 and the device. The SRU520 does not respond properly to commands. Maybe you are using the wrong code. Try programming the SRU520 again using another code, which is mentioned under the brand of your device, or reset for automatic search to find the right code. If the device still does not respond, call our helpline. The Teletext keys do not work. Find out whether your TV is equipped with Teletext. You have difficulties operating all of the functions on your device. Maybe the SRU520 has to be adapted to the model of the device. Call our helpline for details. Your brand of device is not in the code list. Try to set the SRU520 automatically. See `Automatically setting the remote control'. None of the codes works during manual setting of the remote control. If that is the case, follow the instructions under `Automatically setting the remote control'. · ­ · ­ · ­ · ­ SRU520_87_v6.qxd 26-04-2005 14:38 Pagina 10 Instructions for use 6. Need help? If you have any questions about the SRU520, you can always contact us. You will find our contact details after the code list at the back of this manual. Read this manual carefully before y ...