P-320W 802.11g Wireless Firewall Router Quick Start Guide Version 2.00 Edition 1 10/2006 Table of Contents ENGLISH 3 DEUTSCH 18 ESPAÑOL 37 FRANÇAIS 56 ITALIANO 74 92 SVENSKA 112 131 ENGLISH Overview The P-320W is a broadband router with a built-in four-port 10/100 Mbps switch. The P-320W makes it easy to set up a small home or office network and share Internet access via a broadband (cable/DSL) modem. You should have an Internet account already set up and have been given most of the following information. Table 1 Internet Account Information Your device's WAN IP Address (if given): ______________ DNS Server IP Address (if given): Primary _____________, Secondary ______________ Connection Type: Ethernet PPTP: Service Type: _______________________ User Name: ____________ User Name: ____________ Your WAN IP Address (if given) ____________ Connection ID (if required): ____________ ¦PPPoE (PPPoE) Service Name: ____________ User Name: ____________ Password: ____________ Login Server IP Address: ______________ Password: ____________ Password: ____________ PPTP Server IP Address: ___________ or PPTP Domain Name: ___________ See your User's Guide for background information on all features. The follow lists what you need to do: 1 Hardware Connections 2 Accessing the Web Configurator 3 Internet Access Setup 3 ENGLISH 1 Hardware Connections Do the following to make hardware connections for initial setup. Connect your modem to the "WAN" port using the cable that came with your modem. Connect your computer to a "LAN" port using the included Ethernet cable Use the included power adaptor to connect the POWER socket to an appropriate power source (see the User's Guide for power adaptor specifications by region) 1 2 3 WAN Connection LAN Connection POWER Connection 4 ENGLISH The LEDs After you've made the connections, push in the power button to turn on the Mer produkthjalp finns pa http:// www.support.zyxel.se. Look at the front panel LEDs. When you connect the power, the PWR and WLAN LEDs come on. The LAN and WAN LEDs turn on if the corresponding connections are properly made. 2 Accessing the Web Configurator 1 Launch your web browser. Enter "192.168.1.1" as the web site address. Note: If you do not see the next screen, then please go to section 4.1. 2 The Password window displays. Enter the password ("1234" is the default) and click Login. 3 Change the password in the screen that follows and click Apply. 4 Choose your language from the drop-down list box. Click Apply. 5 ENGLISH Note: The Next button is located on the bottom right of each screen. 5 Click Go to Wizard setup to set up your P-320W for the first time.. 6 Choose your language from the drop-down list box. Click Next to proceed with the Connection Wizard. 3 Internet Access Setup Note: Enter the Internet access information exactly as given to you by your ISP in each wizard screen and then click Next to continue or click Back to return to the previous screen. Current screen information will be lost if you click Back. STEP 1: System Information 1 This screen is optional. You can just click Next. · System Name is for identifying the Mer produkthjalp finns pa http://www.support.zyxel.se. You can enter your computer's "Computer Name". · If you leave the Domain Name blank, the domain name obtained by DHCP from the ISP is used. 6 ENGLISH STEP 2: Wireless LAN Configure ONE of the following wireless security types on the Mer produkthjalp finns pa http:// www.support.zyxel.se: · Auto security: Uses WPA-PSK security with an automatically generated Pre-Shared Key. View the generated Pre-Shared Key in the Wireless LAN screen. Note: Your wireless clients must support WPA-PSK and use the same key. · None: Have no wireless LAN security configured. If you do not enable any wireless security on your Mer produkthjalp finns pa http://www.support.zyxel.se, your network is accessible to any wireless networking device that is within range. · Basic security: WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless network. The higher the WEP Encryption, the higher the security but the slower the throughput. · Extend (WPA-PSK) security: Configure a Pre-Shared Key. Choose this option only if your wireless clients support WPA-PSK. Note: The wireless clients and P-320W must use the same SSID, channel ID and WPA-PSK (if WPAPSK is enabled) or WEP encryption key (if WEP is enabled) for wireless communication. OTIST · OTIST (One-Touch Intelligent Security Technology) allows your P-320W to assign wireless clients the Mer produkthjalp finns pa http://www.support.zyxel.se's SSID and static WEP or WPA-PSK encryption settings. The wireless client must also support OTIST and have OTIST enabled. 7 ENGLISH Auto or No Wireless Security A Enter a unique name to identify the P-320W in the wireless LAN. B Leave the default setting. The P-320W and wireless client must use the same channel ID. C Select a level of wireless security. Choose Auto or None. D For Auto security select Yes to enable OTIST. If you select None select either Yes to enable OTIST or select the No radio button and click Next to configure OTIST later. E The default OTIST Setup Key is "01234567". This key can be changed in the web configurator. Be sure to use the same OTIST Setup Key on the P-320W and wireless clients. A B C D E 8 ENGLISH Basic(WEP) Security A Enter a unique name to identify the P-320W in the wireless LAN. B Leave the default setting. The P-320W and wireless client must use the same channel ID. C Select Basic(WEP) security. D You can generate or manually enter a WEP key by either: Entering a Passphrase (up to 32 printable characters) and clicking Generate. The P-320W automatically generates a WEP key. Or entering manual keys in each Key (1~4) field and selecting ASCII or Hex WEP key input method. E Select 64-bit or 128-bit from the WEP Encryption drop-down list. F Select ASCII or Hex characters. G Select one of the Key radio buttons to use as the default WEP key. H Select Yes to enable OTIST. Select the No radio button and click Next to configure OTIST later. I The default OTIST Setup Key is "01234567". This key can be changed in the web configurator. Be sure to use the same OTIST Setup Key on the P-320W and wireless clients. A B C D E G F D E 9 ENGLISH Extend(WPA-PSK) Security A Enter a unique name to identify the P-320W in the wireless LAN. B Leave the default setting. The P-320W and wireless client must use the same channel ID. C Select WPA-PSK security. D Type a pre-shared key to have a more secure wireless connection than WEP encryption. Type from 8 to 63 case-sensitive ASCII characters.You can set up the most secure wireless connection by configuring WPA in the advanced wireless screen. You need to configure a RADIUS server to do this. E Yes is enabled by default. Select the No radio button and click Next to configure OTIST later. F The default OTIST Setup Key is "01234567". This key can be changed in the web configurator. Be sure to use the same OTIST Setup Key on the P-320W and wireless clients. A B C D D E 10 ENGLISH STEP 3: WAN The wizard attempts to detect which WAN connection type you are using. If the wizard does not detect a connection type, you must select ONE from the drop-down list box. Check with your ISP to make sure you use the correct type: 1 Ethernet 2 PPPoE 3 PPTP. Note: If you were given Internet access settings, enter them in the following fields. Otherwise leave the default settings and just click Next 11 ENGLISH Ethernet Connection A Select Ethernet as your WAN connection type. B Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to D. Or Select Use fixed IP address provided by your ISP to give the P-320W a fixed, unique IP address. C Enter a WAN IP address and WAN IP Subnet Mask of the neighboring device, if you know it. If you do not, leave the default settings. If you were given an IP address and/or DNS server settings, enter them in the fields. Otherwise leave the default settings and just click Next. D Select Factory Default to use the factory assigned default MAC address. A B C D 12 ENGLISH PPPoE Connection A Select PPPoE as your WAN connection type. BType a Service Name (Optional), User Name and Password. C Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to E. Or select Use fixed IP address provided by your ISP to give the P-320W a fixed, unique IP address. D Enter the WAN IP address of the neighboring device, if you know it. If you do not, leave the default settings. If you were given IP address and/or DNS server settings, enter them in the fields. Otherwise leave the default settings and just click Next. E Select Factory Default to use the factory assigned default MAC address. A B C D E 13 ENGLISH PPTP Connection A Select PPTP as your WAN connection type. BType a User Name and Password C Select Get automatically from ISP if your ISP did not assign you a fixed PPTP IP address. Or select Use fixed IP address to give the P-320W a fixed, unique PPTP IP address and subnet mask. D Type a PPTP Server IP Address E Type a Connection ID/Name (if provided) F Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to H. Or select Use fixed IP address provided by your ISP to give the P-320W a fixed, unique IP address. G Enter a WAN IP address and WAN IP Subnet Mask of the neighboring device, if you know it. If you do not, leave the default settings. If you were given IP address and/or DNS server settings, enter them in the fields. Otherwise leave the default settings and just click Next. H Select Factory Default to use the factory assigned default MAC address. 14 ENGLISH A B C D E F G H 15 ENGLISH Internet Access Setup Complete If you have any Internet access problems, follow the on-screen instructions. Click Finish to complete the Connection Wizard. 4 Troubleshooting Note: If your computer cannot automatically communicate with the device, then see the multimedia tutorial on how to set up your computer to receive an IP address dynamically or give it a fixed one in the range specified in section 4.1. PROBLEM None of the LEDs turn on when you connect the Mer produkthjalp finns pa http:// www.support.zyxel.se's power. Cannot access the P-320W from my computer. CORRECTIVE ACTION Make sure that you have the correct power adaptor connected to the Mer produkthjalp finns pa http://www.support.zyxel.se, it is plugged into an appropriate power source. Check all cable connections. If the LEDs still do not turn on, you may have a hardware problem. In this case, you should contact your local vendor. Check the cable connection from your computer to the Mer produkthjalp finns pa http://www.support.zyxel.se. If the Mer produkthjalp finns pa http://www.support.zyxel.se's IP address has changed, then enter the new one as the website address. Make sure your computer's IP address is in the same subnet as the Mer produkthjalp finns pa http://www.support.zyxel.se's IP address (see section 4.1). Ping the P-320W from a computer on the LAN. Make sure your computer's Ethernet adapter is installed and functioning properly. In the computer, click Start, (All) Programs, Accessories and then Command Prompt. In the Command Prompt window, type "ping" followed by the Mer produkthjalp finns pa http://www.support.zyxel.se's LAN IP address (192.168.1.1 is the default) and then press [ENTER]. The P-320W should reply; otherwise see section 4.1. 16 ENGLISH PROBLEM Cannot access the P-320W from my computer (continued). CORRECTIVE ACTION Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later with JavaScript enabled. Make sure you enter the password correctly (the field is case sensitive). If you've forgotten the Mer produkthjalp finns pa http://www.support.zyxel.se's password, use the RESET button. Press the button in for about 10 seconds (the WAN light turns off and then on again), then release it. It returns the P-320W to the factory defaults (password is 1234, LAN IP address 192.168.1.1 etc.). Cannot access the Internet. Verify the Internet connection settings in the wizard. Make sure you entered the correct user name and password if you are using PPPoE or PPPoA. 4.1 Set Up Your Computer's IP Address This section shows you how to set your Windows NT/2000/XP computer to automatically get an IP address. This ensures that your computer can communicate with your Mer produkthjalp finns pa http:// www.support.zyxel.se. Refer to your User's Guide for detailed IP address configuration for other Windows and Macintosh computer operating systems. 1 In Windows XP, click start, Control Panel. In Windows 2000/NT, click Start, Settings, Control Panel. 2 In Windows XP, click Network Connections. In Windows 2000/NT, click Network and Dial-up Connections. 3 Right-click Local Area Connection and then click Properties. 4 Select Int ...